Free Energy: Symmetrical Tesla Transformer - Early Circuit Diagram
A device by Donald Lee Smith - a free energy legend of the 90s - is said to be a generator of radiant energy from an electronic circuit. It is basically a Tesla coil-like structure (correctly called a Tesla transformer).
 |
| Symmetrical Tesla Transformer |
Hidden technology researcher Patrick Kelly has collected documents and looked at how Donald Lee Smith's device works in practice, then came up with a circuit diagram.
 |
| Symmetrical Tesla Transformer - Early Circuit Diagram |
I have looked at the circuit and the actual device and made a correlation between the electronic components in the device (generator) compared to the circuit. The main components are labeled as shown below, and then compared to better understand this primitive basic circuit.
Table of information about the blocks on the free energy generator:
Label | Device in Photo | Function | Corresponding in Schematic |
|---|---|---|---|
A | Diode Bridge | Converts AC to DC for system operation | 13. Diode Bridge |
B | Yellow Induction Coil | Pure induction coil (L-1 and L-2), creates self-oscillations and transfers energy | 3. High Voltage Induction (L1 + L2) |
C | Capacitor Bank | Stores and stabilizes DC energy after rectification | 12. Capacitor Bank |
D | White Resonant Coil | Auxiliary induction or resonance coil assisting energy transfer | 6 / 6a / 7. Induction Transfer and Receiving Coils |
E | Small Battery Pack | Provides initial DC power source (6V/12V battery) | 1. Gelecit 6V/12V Battery |
F | Wall Adapter | External AC-DC supply for charging or startup assistance | Auxiliary Power (not numbered) |
G | Controller Box | Handles voltage regulation or signal management | 14 / 15. Voltage Divider or Inverter Circuit |
 |
| Early Circuit Diagram for comparison with the table above |
Components 1 to 7 in the symmetrical circuit closely mirror the structure of a traditional Tesla coil. In both cases, a high-voltage source charges a capacitor (4), which discharges across a spark gap (5) into a primary coil (part of 3), creating oscillations. These oscillations induce high-frequency energy into secondary coils (6 and 6a), just like the secondary winding in a classic Tesla coil.
 |
| Tesla coil |
The key difference is that this design adds a symmetrical coil (7) opposite 6a, forming a balanced dual-secondary system. This symmetry could enhance energy feedback and stability, aiming to optimize resonance and possibly tap into overunity effects - something a standard Tesla coil, with only one secondary, does not inherently achieve.
Talking About Symmetrical Tesla Transformer Circuit Diagram - Primitive Circuit Diagram:
it is probably worth mentioning some of the main points which Don Smith appears to be making. There are some very important points being made here, and grasping these may make a considerable difference to our ability to tap into the excess energy available in our local environment. There are four points worth mentioning:
1. Voltage. We tend to view things with an 'intuitive' view, generally based on fairly simple concepts. For example, we automatically think that it is more difficult to pick up a heavy object than to pick up a light one. How much more difficult? Well, if it is twice as heavy, it would probably be about twice as much effort to pick it up. This view has developed from our experience of things which we have done in the past, rather than on any mathematical calculation or formula.
Well, how about pulsing an electronic system with a voltage? How would the output power of a system be affected by increasing the voltage? Our initial 'off-the cuff' reaction might be that the power output might be increased a bit, but then hold on… we've just remembered that Watts = Volts x Amps, so if you double the voltage, then you would double the power in watts. So we might settle for the notion that if we doubled the voltage then we could double the output power. If we thought that, then we would be wrong.
Don Smith points out that as capacitors and coils store energy, if they are involved in the circuit, then the output power is proportional to the square of the voltage used. Double the voltage, and the output power is four times greater. Use three times the voltage and the output power is nine times greater. Use ten times the voltage and the output power is one hundred times greater !
Don says that the energy stored, multiplied by the cycles per second, is the energy being pumped by the system. Capacitors and inductors (coils) temporarily store electrons, and their performance is given by:
Capacitor formula: W = 0.5 x C x V2 x Hz where:
W is the energy in Joules (Joules = Volts x Amps x seconds) C is the capacitance in Farads V is the voltage Hz is the cycles per second
Inductor formula: W = 0.5 x L x A2 x Hz where:
W is the energy in Joules
L is the inductance in henrys
A is the current in amps
Hz is the frequency in cycles per second
You will notice that where inductors (coils) are involved, then the output power goes up with the square of the current. Double the voltage and double the current gives four times the power output due to the increased voltage and that increased output is increased by a further four times due to the increased current, giving sixteen times the output power.
2. Frequency. You will notice from the formulas above, that the output power is directly proportional to the frequency "Hz". The frequency is the number of cycles per second (or pulses per second) applied to the circuit. This is something which is not intuitive for most people. If you double the rate of pulsing, then you double the power output. When this sinks in, you suddenly see why Nikola Tesla tended to use millions of volts and millions of pulses per second.
However, Don Smith states that when a circuit is at it's point of resonance, resistance in the circuit drops to zero and the circuit becomes effectively, a superconductor. The energy for such a system which is in resonance is:
Resonant circuit: W = 0.5 x C x V2 x (Hz)2 where:
W is the energy in Joules
C is the capacitance in Farads
V is the voltage
Hz is the cycles per second
If this is correct, then raising the frequency in a resonating circuit has a massive effect on the power output of the device. The question then arises: why is the mains power in Europe just fifty cycles per second and in America just sixty cycles per second? If power goes up with frequency, then why not feed households at a million cycles per second? One major reason is that it is not easy to make electric motors which can be driven with power delivered at that frequency, so a more suitable frequency is chosen in order to suit the motors in vacuum cleaners, washing machines and other household equipment.
However, if we want to extract energy from the environment, then we should go for high voltage and high frequency. Then, when high power has been extracted, if we want a low frequency suited to electric motors, we can pulse the already captured power at that low frequency.
It might be speculated that if a device is being driven with sharp pulses which have a very sharply rising leading edge, that the effective frequency of the pulsing is actually determined by the speed of that rising edge, rather than the rate at which the pulses are actually generated. For example, if pulses are being generated at, say, 50 kHz but the pulses have a leading edge which would be suited to a 200 kHz pulse train, then the device might well see the signal as a 200 kHz signal with a 25% Mark/Space ratio, the very suddenness of the applied voltage having a magnetic shocking effect equivalent to a 200 kHz pulse train.
After checking, Donald Lee Smith is not a myth of free energy created by fiction. The circuit diagram has a scientific basis for the Ether to create free energy. Modern electrical science today cannot explain the operation of the free energy generator. Because the content has been basically omitted from the science of the old world. Moreover, the educational policy is to invest in developing wrong theories. If you need the operating principle of the above device according to the Field theory, you can contact me via messages on the social networks linked to this website.
Recommended for you:
⁂ Self-powered generator with feedback circuit for input.
※ Transistorized snap-off technology to harness energy from dielectric inertia.
※ This is a modern version of the self-powered generator, suitable for today's manufacturing - just buy the electronic components and electrical equipment to assemble, then expand the scale and increase the power of the machine. In addition, the plan has many other modern and unique methods!
